CONTOH KONFIGURASI TOPOLOGI MELALUI CISCO (=>JARKOM<=)

Konfigurasi.....?
ROUTER=>0
Router>en
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#hostname GAD
GAD(config)#int f0/0
GAD(config-if)#ip add 192.168.1.0 255.255.255.0
Bad mask /24 for address 192.168.1.0
GAD(config-if)#ip add 192.168.1.1 255.255.255.0
GAD(config-if)#no sh

GAD(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

GAD(config-if)#exit
GAD(config)#int s0/0/0
GAD(config-if)#ip add 192.168.2.2 255.255.255.0
GAD(config-if)#clock rate 64000
GAD(config-if)#no sh

%LINK-5-CHANGED: Interface Serial0/0/0, changed state to down
GAD(config-if)#
%LINK-5-CHANGED: Interface Serial0/0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/0, changed state to up

GAD(config-if)#exit
GAD(config)#router rip
GAD(config-router)#network 192.168.1.0
GAD(config-router)#network 192.168.2.0


ROUTER=>1
Router>en
Router#config t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#hostname BHM
BHM(config)#int f0/0
BHM(config-if)#ip add 192.168.3.1 255.255.255.0
BHM(config-if)#no sh

BHM(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

BHM(config-if)#exit
BHM(config)#int s0/0/0
BHM(config-if)#ip add 192.168.2.1 255.255.255.0
BHM(config-if)#no sh

BHM(config-if)#
%LINK-5-CHANGED: Interface Serial0/0/0, changed state to up

BHM(config-if)#exit
BHM(config)#int s0/0/1
BHM(config-if)#ip a
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/0, changed state to up

% Ambiguous command: "ip a"
BHM(config-if)#ip add 192.168.4.1 255.255.255.0
BHM(config-if)#clock rate 64000
BHM(config-if)#no sh

%LINK-5-CHANGED: Interface Serial0/0/1, changed state to down
BHM(config-if)#
%LINK-5-CHANGED: Interface Serial0/0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/1, changed state to up

BHM(config-if)#exit
BHM(config)#router rip
BHM(config-router)#network 192.168.2.0
BHM(config-router)#network 192.168.3.0
BHM(config-router)#network 192.168.4.0


ROUTER=>2
Router>en
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#hostname cisco
cisco(config)#int fa0/0
cisco(config-if)#ip add 192.168.5.1 255.255.255.0
cisco(config-if)#no sh

cisco(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

cisco(config-if)#exit
cisco(config)#router rip
cisco(config-router)#network  192.168.5.0
cisco(config-router)#network  192.168.4.0
cisco(config-router)#exit
cisco(config)#int s0/0/1
cisco(config-if)#ip add 192.168.5.2 255.255.255.0
% 192.168.5.0 overlaps with FastEthernet0/0
cisco(config-if)#ip add 192.168.3.3 255.255.255.0
cisco(config-if)#clock rate 64000
cisco(config-if)#no sh

cisco(config-if)#
%LINK-5-CHANGED: Interface Serial0/0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/1, changed state to up